Cam kết 100% chính hãng
Hoàn tiền 111% nếu hàng giả
Giao hàng nhanh chóng & an toàn
Hàng hóa đầy đủ CO, CQ
Hỗ trợ 24/7
Khuyến mãi đặc biệt !!!
Áp dụng Phiếu quà tặng/ Mã giảm giá theo ngành hàng.
Miễn phí vận chuyển với đơn hàng từ 10.000.000đModule RS-485 DCON 8 kênh đầu vào bộ đếm tốc độ cao HSC+8 kênh đầu ra PWM ICP DAS I-7088D-G/S CR
Features
• 8-channel PWM Output and 8-channel Counter Input
• Burst Mode and Continuous Mode for PWM Output
• Software and Hardware Trigger Mode for PWM Output
• Individual and Synchronous PWM Output
• High-speed Counters
• 4 kV ESD and EFT Protection
• Dual Watchdog
• Wide Operating Temperature Range: -25 to +75°C
Introduction
The I-7088 provides 8-channel PWM (Pulse Width Modulation) Output and 8-channel Counter Input, and can be used to develop powerful and cost-effective analog control systems. PWM is a powerful technique for controlling analog circuits that uses the Digital Output to generate a waveform with a variable duty cycle and frequency which can then be used to control an analog circuit in applications such as controlling the position or speed of motors, the brightness of lamps, or the speed of fans, etc. Either burst mode or continuous mode can be used for the PWM output depending on the application. In addition, all Digital Input channels can be used as high-speed counters with a speed of up to 1 MHz. The M-7088 supports both the Modbus RTU and the DCON protocols, which can be configured via software, and all hardware specifications are the same as the I-7088. The I-7088(D)/S and M-7088(D)/S allows the load voltage to be increased from +3.5 to +50 V for the 8-channels PWM (Pulse Width Modulation) output and the 8-channels high-speed counter.
Specification
| CPU Module | |
|---|---|
| Watchdog Timer | Yes, Module (1.6 Seconds), Communication (Programmable) |
| Display | |
|---|---|
| Type | 5-Digit 7 Segment LED Display |
| Memory | |
|---|---|
| Battery Backup | Yes |
| Isolation | |
|---|---|
| Intra-module Isolation | 2500 VDC |
| EMS Protection | |
|---|---|
| EFT (IEC 61000-4-4) | ±4 kV for Power Line |
| ESD (IEC 61000-4-2) | ±4 kV Contact for each Terminal |
| LED Indicators | |
|---|---|
| Status | 1 x Power and Communication |
| Digital Output | |
|---|---|
| Type | PWM, TTL |
| Sink/Source (NPN/PNP) | Sink |
| Load Voltage | +5 ~ +50 VDC |
| Max. Load Current | Sink: +50 VDC @ 200 mA/Channel |
| PWM | |
|---|---|
| Channels | 8 |
| Type | Hardware or Software |
| Load Voltage | +5 ~ +50 VDC |
| Frequency | 1 Hz ~ 500 KHz |
| Duty Cycle | 0.1 to 99.9% |
| Mode | Burst, Continuous |
| Burst Count | 1 to 65535 |
| Trigger Start | Hardware or Software |
| Counter/Frequency/Encoder Input | |
|---|---|
| Channels | 8 |
| Type | Counter |
| Sink/Source (NPN/PNP) | Sink |
| Counter/Encoder Bits | 32-bit |
| ON Voltage Level | +3.5 ~ +50 VDC |
| OFF Voltage Level | +1 VDC Max. |
| Counter Mode | Up |
| Max. Speed | 1 MHz |
| COM Ports | |
|---|---|
| Ports | 1 x RS-485 |
| Baud Rate | 1200 ~ 115200 bps |
| Data Format | (N, 8, 1) (N, 8, 2) (E, 8, 1) (O, 8, 1) |
| Protocol | DCON |
| Power | |
|---|---|
| Reverse Polarity Protection | Yes |
| Input Range | +10 ~ +30 VDC |
| Consumption | 3.4 W |
| Mechanical | |
|---|---|
| Dimensions (mm) | 123 x 72 x 35 (W x L x H) |
| Installation | DIN-Rail |
| Environmental | |
|---|---|
| Operating Temperature | -25 ~ +75 °C |
| Storage Temperature | -40 ~ +85 °C |
| Humidity | 10 ~ 95% RH, Non-condensing |
Download
Ordering information
| I-7088D-G/S CR | 8-ch PWM Output and 8-ch High-speed Counter Input Module (50 VDC) with LED Display using DCON Protocol (Gray Cover) (RoHS) Includes DN-8P8C-CA (External Board and Cable) |
