Bộ chuyển đổi CAN sang Quang (Dual Fiber, Single Mode, SC, 30KM) ICP DAS I-2533CS CR

Thương hiệu: ICP DAS | Tình trạng: Còn hàng

Liên hệ

CAN to Single-mode Fiber Bridge

THÔNG TIN SẢN PHẨM

Feature

Fiber Type: SC ; Single mode ; 100 Base-FX
Maximum transmission distance up to 30 km at any CAN baud rate
NXP TJA1042 CAN transceiver
2500 Vrms isolation on the CAN side
Supports both CAN 2.0A and CAN 2.0B
Fully compatible with the ISO 11898-2 standard
Rotary switch for CAN baud rate configuration
Build-in switch for 120 Ω terminal resistor
Removable terminal block, Mount easily on DIN-Rail
Allows user-defined CAN baud rate
Fiber broken line detection
Utility tool for CAN message filter configuration
The CAN port with the same Group ID can communicate with each other

Introduction

The I-2533CS is a local CAN bridge used to establish a connection between two CAN bus system via single mode fiber optic transmission medium. In order to solve the problem between CAN and fiber transmission medium, the I-2533CS is specially designed for converting the electrical CAN bus signal to fiber optic cables. I-2533CS has three more important features. First, the transmission distance limitation of the CAN bus system will not affected due to the different CAN baud rate. It means that the total CAN bus working distance can be extended. Second, the bus error on one CAN network will not affect the operation of another CAN network. Finally, the two CAN network can communication with each other by using different CAN baud rate for highly flexibility.

The I-2533CS series is designed for single mode fiber, and allow to extern CAN bus to maximum 30 km. Besides, I-2533CS provides the group function, which is the basic message router. Users can decide the CAN message flows between several CAN bus systems. I-2533CS series also provides the utility tool for user-defined baud rate and filter configuration. By using this tool, it is allowed to have user-defined baud rate and CAN message filter. When users use the I-2533CS series on two CAN network with different CAN baud rate, it may be useful to reduce the bus loading of the network which has low baud rate.

Application

Control System
Building Automation
Factory Automation
Distributed data acquisition

Specifications

LED Indicators
Status	1 x Power 3 x CAN status 2 x Fiber status

COM Ports
Ports	1 x RS-232 (Utility Port)

Fiber
Ports	Single-Mode; SC Duplex connector x 1; 100 Base-FX
Fiber Cable	8.3/125, 8.7/125, 9/125 or 10/125 μm
Wavelength	1310 nm
TX Output	-15 dBmMin. , -8 dBm Max.
RX Sensitivity	-34 dBm Max.
RX Overload	-5 dBm Max.
Budget	19 dBm
Propagation Delay	190 us (*Note1)
Distance Between Stations	30 km (9/125 μm recommended)

CAN
Ports	1
Baud Rate	10 k ~ 1 M bps
Isolation	500 Vrms on the CAN side
Terminal Resistor	Switch for 120Ω terminal resistor
Specification	ISO 11898-2, CAN 2.0A and CAN 2.0B
Filter	Yes

Power
Input Range	+10 VDC ~ +30 VDC
Consumption	3 W

Mechanical
Casing	Plastic
Dimensions (mm)	33 x 126 x 101 (W x L x H)
Installation	DIN-Rail

Environment
Operating Temperature	-25 ~ +75 °C
Storage Temperature	-30 ~ +80 °C
Humidity	10 ~ 90% RH, Non-condensing

Specification Memo

Note1: The propagation delay depends on the CAN Bus baud rate and the CAN message format. This value has been tested using a CAN baud rate of 1 Mbps, the CAN ID 0x12345678 and 8 bytes of data with a value of 0xFF.

Download

Datasheet

Documents

Ordering Information

I-2533CS CR

CAN to Single-mode Fiber Bridge; 1 (30 km) single-mode, SC connector (RoHS)

Bộ chuyển đổi CAN sang Quang (Dual Fiber, Single Mode, SC, 30KM) ICP DAS I-2533CS CR

Sản phẩm đã được thêm vào giỏ hàng

Sản phẩm đã được thêm vào giỏ hàng