Module điều khiển đèn chiếu sáng ICP DAS LC-102H CR

Thương hiệu: ICP DAS | Tình trạng: Còn hàng

Liên hệ

2-CH Lighting Control Module with AC Load Current Measurement (2 AC DI + 2 Relay output)

THÔNG TIN SẢN PHẨM

Feature

High Power Relay Output to Turn On/Off the Lighting
Number of Lighting Fixtures That Can Be Connected:
- Incandescent Lamp: 40 W/ 220 VAC * 5 Sets
- LED(Electronic ballast): 40 W/ 220 VAC *8 Sets
0 to 5 A AC power Load Current Measurement Relay output
Isolated AC Digital Input
Node Addresses by Hardware Configuration
Low Power Consumption
Modbus RTU and DCON Protocols

Introduction

The LC lighting control module is easy-to-use and requires no specialist skills to install and operate, and no software is needed in order to control the lighting control channels.

The LC-102H is a 2-channel lighting control module with AC load current measurement which provides 2-channel high power relay output and 2-channel AC digital input.

The AC load current measurement is provided in the relay control loop. This function not only allows the user to know the load current value, but also through the measurement of the load current value, it can be used to know the switching state of the relay, whether the load is working normally in the light control loop, or the relay is stuck and cannot be switched.

The input channel can directly control the relay ON and OFF sequence without the host command.

When required, the module can be communicated with the Modbus RTU protocol, and an added benefit is that different addresses can be set for Modbus RTU communication via hardware configuration.

Application

Specifications

Software
Function	Local and Remote Direct Control Relay ON/OFF and Remote Status Monitoring

EMS Protection
EFT (IEC 61000-4-4)	±4 kV for Power
ESD (IEC 61000-4-2)	±4 kV Contact for each Terminal
Surge (IEC 61000-4-5)	±2 kV for Power

LED Indicators
Status	1 LED as Power Indicator

Digital Input
Channels	2
Type	Wet Contact, 90 ~ 240 VAC
ON Voltage Level	65 VAC
OFF Voltage Level	56 VAC
Isolation	3000 VDC
Input Impedance	68 KΩ, 2W

Relay Output
Channels	2
Type	Power Relay, Form C (SPDT N.O+N.C..)
Contact Rating	30 A @ 250 VAC
AC Load Current Measurement	Yes, 0 ~ 5 A range with 3% of FSR Accuracy.
Operate Time	15 ms Max
Release Time	22 ms Max.
Electrical Endurance	100,000 ops.
Mechanical Endurance	10,000,000 ops
Power on Value	Yes
Safe Value	Yes
Application Specification	(1).Incandescent Lamp: 40W/ 220VAC * 5 Sets (2).LED(Electronic ballast): 40W/ 220VAC *8 Sets

COM Ports
Ports	1 x RS-485
Baud Rate	Hardware Configuration: Fixed 9600 bps Software Configuration: 1200 to 115200 bps
Data Format	N,8,1/O,8,1/E,8,1/N,8,2
Protocol	Modbus RTU/DCON

Ethernet
Node Address	32 to 63 for hardware configuration

Power
Reverse Polarity Protection	Yes
Input Range	10 ~ 30 VDC
Consumption	2.8 W Max.

Mechanical
Dimensions (mm)	72 mm x 95 mm x 57 mm
Installation	DIN-Rail

Environment
Operating Temperature	-25 ~ +75°C
Storage Temperature	-30 ~ +75°C
Humidity	10 ~ 95% RH, Non-condensing

Download

Datasheet

Documents

Ordering Information

LC-102H CR

2-CH Lighting Control Module with AC Load Current Measurement (2 AC DI + 2 Relay output) (RoHS)

Module điều khiển đèn chiếu sáng ICP DAS LC-102H CR

Sản phẩm đã được thêm vào giỏ hàng

Sản phẩm đã được thêm vào giỏ hàng