Cam kết 100% chính hãng
Hoàn tiền 111% nếu hàng giả
Giao hàng nhanh chóng & an toàn
Hàng hóa đầy đủ CO, CQ
Hỗ trợ 24/7
Khuyến mãi đặc biệt !!!
Áp dụng Phiếu quà tặng/ Mã giảm giá theo ngành hàng.
Miễn phí vận chuyển với đơn hàng từ 10.000.000đModule điều khiển độ sáng đèn chiếu sáng ICP DAS LC-223H CR
Feature
Introduction
The LC-223H is an easy-to-use dimming ballast control module that can be easily installed and operated without requiring specialist knowledge or skills. The brightness of a fluorescent lamp can be controlled using a dimmer, either via digital input or a host controller. The digital input can be used to directly control the light value of the luminous flux in sequence from 10% to 100%, without the need for a remote host controller. 4 kV ESD,2kV SURGE protection and 2500 VDC intra-module isolation are also provided. When required, communication with the LC-223H is programmable based on the Modbus RTU/DCON protocol, with the added benefit that diff erent addresses can be set via hardware configuration.
Application
Specifications
| Isolation | |
|---|---|
| Intra-module Isolation | 2500 VDC |
| EMS Protection | |
|---|---|
| EFT (IEC 61000-4-4) | ±4 kV for Power |
| ESD (IEC 61000-4-2) | ±4 kV contact for each Terminal ±4 kV Air for Random Point |
| Surge (IEC 61000-4-5) | ±2 kV for Power |
| LED Indicators | |
|---|---|
| Status | 1 LED as Power Indicator |
| Analog Output | |
|---|---|
| Channels | 1 |
| Type | 0 ~ 20 mA, 4 ~ 20 mA, 0 ~ 10 V, 1 ~ 10 V |
| Resolution | 12-bit |
| Accuracy | ±0.1% of FSR |
| DA Output Response Time | 10 ms |
| Voltage Output Capability | 20 mA |
| Current Load Resistance | 450 Ω |
| Digital Input | |
|---|---|
| Channels | Dry Contact: 2 for the Dimming Trigger Wet Contact: 1 for the Wall Switch Control |
| Type | Dry + Wet Contact |
| ON Voltage Level | Wet: 65 VAC ~ 240 VAC Dry: Close to GND |
| OFF Voltage Level | Wet: 58 VAC Max. Dry: Open |
| Relay Output | |
|---|---|
| Channels | 1 |
| Type | Power Relay, Form A (SPST N.O.) |
| Contact Rating | 16 A (Res. load) (1).250 VAC (Recommend Working Current 1.5 A) |
| Operate Time | 10 ms Max. |
| Release Time | 5 ms Max. |
| Electrical Endurance | 120,000 ops. |
| Mechanical Endurance | 5,000,000 ops. |
| Power on Value | Yes, programmable |
| Safe Value | Yes, programmable |
| Application Specification | (1).Incandescent Lamp: 40W/220VAC * 8 Sets (2).LED (Electronic ballast): 40W/220VAC * 10 Sets |
| COM Ports | |
|---|---|
| Ports | 1 x RS-485 |
| Baud Rate | 1200 ~ 115200 bps |
| Data Format | (N, 8, 1) |
| Protocol | DCON, Modbus RTU |
| Power | |
|---|---|
| Reverse Polarity Protection | Yes |
| Consumption | 1.5 W Max. |
| Powered from Terminal Block | Yes, 10 ~ 30 VDC |
| Mechanical | |
|---|---|
| Dimensions (mm) | 72 x 100 x 59 (W x L x H) |
| Installation | DIN-Rail |
| Environment | |
|---|---|
| Operating Temperature | -25 ~ +75°C |
| Storage Temperature | -30 ~ +80°C |
| Humidity | 10 ~ 95% RH, Non-condensing |
Download
Ordering Information
| LC-223H CR | 1-channel Dimmer Control Module with 2-channel Dry Contact Input Trigger (RoHS) |
